R.W-15

Single Turn Wire Wound Potentiometer, R.W-15

Model R.W-15 is the highest power ratted panel-mounted Potentiometer from PANKAJ has thermosetting housing, good linearity coupled with longer rotational life expectancy in its class. Incidentally, this is the only product of its kind in the market.

Features

  • Brass Nickel Plated Bush & Spindle
  • Tin-Plated Terminals
  • Thermoset Housing

Electrical Specifications

Resistance Range 50Ω to 50KΩ
Resistance Tolerance +10% Standard, +5% Special
Power Rating 15 Watt @ 40°C
End Resistance 0.2Ω or 0.02 % which ever is greater
Elec. Angle of Rotation 310° + 15°
Maximum Working Voltage 500VDC
Insulation Resistance 500MΩ @ 500 VDC
Voltage Proof 1500VAC for 1 Min. At Sea level
TCR of Resistance Wire 150ppm/°C
Rotational Life Expectancy 20,000 Cycles at 15 RPM
Temperature Range 0 – 70°C.

Mechanical Specifications

Housing Diameter 90mm
Housing Length 38mm
Shaft Diameter 6.3mm
Shaft Length 40mm
Bush Mounting 3/8″ x 32 TPI, 10mm Long & Three M3 screws @ 36 PCD
Mechanical Angle of Rot. 330°+15°

Applications

  • Railway Battery Charger,
  • Power Supplies,
  • AC/DC Motor Drives,
  • Process Control Equipments,
  • Test & Measuring Instruments,
  • Control Panels, Offset Settings & many more.

Dimensional Diagram

s-rw-15-d

Ordering Information Example: R.W-15, 10K, 40 mm

Model No. Resistance Value Shaft Length in mm
R. W-15 50, 100, 250, 500, 1K, 2K, 2K5, 3K, 5K,
10K, 20K, 25K, 50K, 100K		 40mm or as required

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

R.W-7.5

Single Turn Wire Wound Potentiometer, R.W-7.5

PANKAJ, the popular brand for panel mounted Wire Wound Potentiometers, manufactures model R. W. 7.5 product best suited for Railways & battery charges applications etc. This product is also available with Screw / nut type stud terminals. Incidentally this is the only product of its kind in market.

Features

  • Brass Nickel Plated Bush & Spindle
  • Tin Plated Terminals
  • Thermoset Housing

Optional Features

  • Various Shaft Lengths and Designs
  • Stud type terminals

Electrical Specifications

Resistance Range 50Ω to 50KΩ
Resistance Tolerance +10% Standard, +5% Special
Power Rating 7.5 Watt @ 40°C
End Resistance 0.2Ω or 0.02 % which ever is greater
Elec. Angle of Rotation 265° + 15°
Maximum Working Voltage 500VDC
Insulation Resistance 500MΩ @ 500VDC
Voltage Proof 1500VAC for 1 Min. At Sea level
TCR of Resistance Wire 150ppm/°C
Rotational Life Expectancy 20,000 Cycles at 15 RPM
Temperature Range 0 – 70°C.

Mechanical Specifications

Housing Diameter 48mm
Housing Length 38mm
Shaft Diameter 6.3mm
Shaft Length 41mm
Bush Mounting 3/8″ x 32 TPI, 10mm Long
Mechanical Angle of Rot. 285° + 15°

Applications

  • Railway Battery Chargers,
  • Power Supplies,
  • AC/DC Motor Drives,
  • Process Control Equipments,
  • Test and Measuring Instruments,
  • Control Panels,
  • Offset Settings & many more.

Dimensional Diagram

s-rw-75-d

Other Options

s-rw-75-op

s-rw-75-op-d

Ordering Information Example: R.W-7.5, 20K, 41mm

Model No. Resistance Value Shaft Length in mm Other Options
R. W-7.5 50, 100, 250, 500, 1K, 2K, 2K5, 3K, 5K,
10K, 20K, 25K, 50K		 41mm or as required P – Locking Plate
L – Shaft Locking Nut

 

R.W-5

PANKAJ, the most popular brand for panel mounted Wire Wound Potentiometers, manufactures model R.W.5 product best suited for Railways & battery charges applications etc. This product is also available with Screw / nut type stud terminals. Incidentally this is the only product of its kind in market..

Features

  • Brass Nickel Plated Bush & Spindle
  • Tin Plated Terminals
  • Thermoset Housing

Optional Features

  • Anti Rotating Mounting Plate

Electrical Specifications

Resistance Range 50Ω to 50KΩ
Resistance Tolerance +10% Standard, +5% Special
Power Rating 5 Watt @ 40°C
End Resistance 0.2Ω or 0.02% which ever is greater
Elec. Angle of Rotation 285°+15°
Maximum Working Voltage 500VDC
Insulation Resistance 500MΩ @ 500 VDC
Voltage Proof 1500VAC for 1 Min. At Sea level
TCR of Resistance Wire 150ppm/°C
Rotational Life Expectancy 20,000 Cycles at 15 RPM
Temperature Range 0 – 70°C.

Mechanical Specifications

Housing Diameter 48mm
Housing Length 28mm
Shaft Diameter 6.3mm
Shaft Length 25mm
Bush Mounting 3/8″ x 32 TPI, 10mm Long
Mechanical Angle of Rot. 290°+15°

Applications

  • Power Supplies,
  • Battery Chargers,
  • Process Control Equipments,
  • Test and Measuring Instruments,
  • Control Panels,
  • Offset Settings & many more.

Dimensional Diagram

Ordering Information Example: R.W-5, 10K, 25mm

Model No. Resistance Value Shaft Length in mm Other Options
R. W-5 50, 100, 250, 500, 1K, 2K, 2K5, 3K, 5K,
10K, 20K, 25K, 50K		 25mm P – Locking Plate
L – Shaft Locking Nut

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

R.W-1

The most sought after product in Domestic and International market from PANKAJ, model R.W-1 marks it’s presence since over five decades. Offers best value for money in manual setting application.

Features

  • Brass Nickel Plated Bush & Spindle
  • Tin Plated Terminals
  • High Grade Engineering Moulded Plastic Housing

Optional Features

  • Anti Rotating Mounting Plate
  • Various Shaft Lengths and Designs
  • Shaft Locking Nut

Electrical Specifications

Resistance Range 25Ω to 25KΩ
Resistance Tolerance +10% Standard, +5% Special
Power Rating 1 Watt @ 40°C
End Resistance 0.2Ω or 0.02% which ever is greater
Elec. Angle of Rotation 265° + 15°
Maximum Working Voltage 250VDC
Insulation Resistance 200MΩ @ 500VDC
Voltage Proof 750VAC for 1 Min. At Sea level
TCR of Resistance Wire 150 ppm/°C
Rotational Life Expectancy 20,000 Cycles at 15 RPM
Temperature Range 0 – 70°C.

Mechanical Specifications

Housing Diameter 24mm
Housing Length 16mm
Shaft Diameter 6.3mm
Shaft Length 19mm or 25mm Standard
Bush Mounting 3/8″ x 32 TPI, 10mm long
Mechanical Angle of Rot. 285° + 15°

Applications

  • Temperature Controllers,
  • Power Supplies, AC/DC Motor Drives,
  • Process Control Equipments,
  • Test and Measuring Instruments,
  • Control Panels, Offset Settings & many more.

Dimensional Diagram

s-rw-1-d

Other Options

s-rw-1-1 s-rw-1-2 s-rw-3

Ordering Information Example: R.W-1, 10K, 25mm

Model No. Resistance Value Shaft Length in mm Other Options
R. W-1 25, 50, 100, 150, 200, 250, 500, 1K,
2K, 2K5, 3K, 5K, 10K, 20K, 25K		 Standard: 19mm or 25mm Other shaft length:
12.7mm, 16mm, 16 Flat, 19Flat		 F – Flattened Shaft
P – Locking Plate
L – Shaft Locking Nut

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice.

Single Turn Conductive Plastic Potentiometers SCP-25

 

Conductive Plastic Single Turn Panel Mounting Potentiometers SCP-25 from PANKAJ offers long rotational life, stable output in wide temperature range, high moisture environment, with infinite resolution for manual or mechanized application in variety of fields e.g. Drives, Automation etc.

Features

  • Infinite Resolution, low CRV
  • Gold Plated Wiper & PCB
  • Long Rotational Life
  • Sturdy Construction
  • Brass Nickel Plated Bush and Shaft
  • Thermoplastic Housing
  • Ralimat Connector Compatible Termination
  • Various Shaft Lengths and Designs

Electrical Specifications

Standard Resistance Values 1K, 5K & 10KΩ Others on request
Resistance Range
Standard
Spacial		 ± 25%
± 15%
Power Rating 1 Watt @ 40˚C
Resolution Essentially Infinite
Rotational Life Expectancy 1 Lakh Shaft Revolutions
Temp. Coefficient of Resistance ± 500 ppm/˚C
Maximum Wiper Current 1 mA
Effective Electrical Angle 300˚
Dielectric Strength at Sea Level Min. 1000VAC for 1 minute
Temperature Range 0˚ to 100˚C

Mechanical Specifications

Housing Diameter 25mm
Housing Length 12mm
Shaft Diameter 6.3mm
Shaft Length 19mm or 25mm
Mounting Bush 3/8” x 32 TPI, 10mm Long
Mechanical Angle of Rotation 330˚

Dimensional Diagram

scp-25-d

Applications

  • Automation,
  • AC/DC Motor Drives,
  • Process Control Equipments,
  • Test and Measuring Instruments,
  • Control Panels,
  • Offset Settings & many more.

Ordering Information Example: SCP-25, 1K, 19mm

Model No. Resistance Value Shaft Length in mm
SCP-25 SCP-25 19mm or 25mm as required Others on request

 

RCP-35

Rotary Conductive Plastic Servo Potentiometer, RCP-35

Conductive Plastic Servo Potentiometer from PANKAJ offers long rotational life, stable output in wide temperature range, high moisture environment, with infinite resolution for manual or mechanized application in variety of fields.

Features

  • Infinite Resolution, Low CRV
  • Gold Plated Wiper & PCB
  • Double Ball Berings
  • White Anodized Aluminum Top
  • Fiber Backelite Housing
  • Relimate Connector PCB
  • Long Rotational Life
  • Sturdy Construction

Electrical Specifications

Standard Resistance Values 1K, 5K & 10KΩ, Others on request
Resistance Tolerance Standard Special ±25% ±15%
Resolution Essentially Infinite
Rotational Life Expectancy 1 Lakh Shaft Revolutions
Temp. Coefficient of Resistance ±500 ppm/˚C
Maximum Wiper Current 1mA
Effective Electrical Angle 355˚
Dielectric Strength at Sea Level Min. 1000VAC for 1 minute
Temperature Range 0˚ to 70˚C
Weight 20gms

Mechanical Specifications

Housing Diameter 35mm
Housing Length 27.5mm
Shaft Diameter 6mm
Shaft Length 15mm
Servo Mounting Three M3 screws @ 20mm PCD
Pilot Diameter 10mm x 1.5mm
Mechanical Angle of Rotation 360˚

Dimensional Diagram

rcp-35-d-1

Applications

  • Drives, Automation,
  • Rotary sensing,
  • Feedback,
  • Tension Control,
  • Valves Control & many more.

Ordering Information Example: RCP-35, 1K

Model No. Resistance Value
RCP-35 1K, 5K, 10K

 

NCP-711-SSI

 10 Bit Absolute Analogue Encoder
Model: NCP-711-SSIE (Serial Synchronous Encoder)

Absolute Analogue Servo Encoder is operating on Hall’s effect principle. There is no metallic moving wiper
contacting to element and hence no wear and tear or sliding electrical noise. Shaft is rotating endlessly in
double ball bearings giving very smooth movement. It has excellent mechanical response with no hysteries
in the output. The Sensor and electronic circuits are enclosed in anodized aluminum housing with IP-65
protection, It is ideal for harsh environment applications.

Features

  • 50 mm Diameter Black Aluminum Anodised housing
  • Double Ball Bearings
  • 8 mm Stainless Steel ‘D’ cut Shaft
  • Servo Mounting or three M3 Screws at 32mm PCD
  • Low operating torque
  • Connector with cable

Specifications

Angle of Rotation 0~360° Clockwise rotation (Endless), can be factory programmed for
double ball bearings giving very smooth movement. It has excellent mechanical response with no hystersis
45°,90°, 180° and Counter Clockwise Rotation (CCW)
Auxiliary Supply (Vss) 9VDC to 30VDC±10%, 25mA max
Output SSI and 5VDC
Total Independent linearity ≤0.7° (with respect to best line fit and over full temperature range) for
V & mA output
Resolution 10 bit (0.35°) over 360° for 360° range
11 bit (0.176°) over 180° for 180° range
12 bit (0.088°) over 90° for 90° range
12 bit (0.088°) over 45° for 45° range
External Magnetic Field Effect Small effect due to Differential measuring
technique & sensor conditioning circuitry. (It is
desirable to mount encoder away from strong
magnetic field, at least 100mm
Maximum Angular Shaft Speed 3000RPM. Number of samples per revolution
decreases as the speed of rotation increases.
Accuracy of output is not affected by Speed
Operating Temperature Range 0°~70°C
Temperature Compensation No external compensation required
Insulation Resistance 2MΩ min. @ 500VDC
H.V. Test No damage for 1 min at 250VAC
Rotational life 100 million
Protection Class IP-65

Wiring Colour Code

Red Vs – 24VDC Supply
Black Gnd – Circuit Ground
White V – 0 to 10VDC, O/P corresponds to 0° to 360° for V & S
Blue Io – 4 to 20mA, O/P corresponds to 0° to 360° for V & S
Brown CS – Chip Select, Normally Heigh, Active Low, Schmitt Trigger Input with
Pull-Up Resistor of ~50KΩ
Grey CLK – Clock, Normally High, clock input of SSI, Schmitt Trigger input, Frequency: >0 to1MHz
Green DO – Data Output of SSI

Functional Description

When CS is at logic low (active), DO will change to High from High Impedance state. After 500ns (CLKFE) time data is latched into shift register with first falling edge of CLK. With subsequent rising edge of CLK pulse, one data bit shifts out at DO. Word contains 16 bit. First 10 bits are angle information D(9:0). D9 is MSB and D0 is LSB of angle information.

Subsequent 6 bits are for system information viz.:

OCF – Offset Compensation Finished; OC algorithm has finished and data is valid if logic High,
COF – Cordic Overflow; Logic High indicates an out of range error in the cordic part, data D(9:0) is invalid.
Send the encoder to factory.
LIN – LINearity Alarm; Field generates a critical output linearity when logic High, data D(9:0) may
still be used but may contain invalid data. Send the encoder to factory.
MagInc – Magnitude Increase, field intensity is increasing, check the external magnetic disturbance.
MagDec – Magnitude Decrease, field intensity is decreasing, check the external magnetic disturbance.
Both above at logic High indicates magnetic field strength is below or above the required limit.
Check for external magnetic influence. If not i.e. field strength is below the desired level, send the encoder
to factory.
Even Parity – bit for transmission error detection of bits 1 to 15 (D9…D0, OCF, COF, LIN, MagInc, DecMag).
Other Functionality:
Sample Rate:
Sampling Rate, n = 60/(RPM x 384μs).
e.g. RPM = 60, then n = 60/(60 x 384 x 10-6) = 2604 samples/second.
MagRngn – Magnet Field Magnitude Range Warning (Optional), it is combination of MagInc and MagDec.
Active Low via open drain output, requires an external pull-up resistor. If the magnetic field is in range,
this output is turned off (logic High).
Diasy Chain: It allows connection of several encoder in series, while still keeping one input for data
transfer in μP (Optional).

Applications

  • Automation,
  • Test and Measuring Instruments,
  • Crane, Angle Measurement,
  • Robotics & many more.

Options

NC711-SSI (Serial Synchronous Interface)
SSI/45°, CW or CCW
SSI/90°, CW or CCW
SSI/180°, CW or CCW
SSI/360°, CW or CCW – (Standard SSI)

Dimensional Diagram

ncp711-ssi

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

NCP-711-S

 10 Bit Absolute Analogue Encoder Model: NCP-711-S (Standard) & V (Voltage)

Absolute Analogue Servo Encoder is operating on Hall’s effect principle. There is no metallic moving wiper contacting to element and hence no wear and tear or sliding electrical noise. Shaft is rotating endlessly in double ball bearings giving very smooth movement. It has excellent mechanical response with no hysteries in the output. The Sensor and electronic circuits are enclosed in anodized aluminum housing with IP-65 protection, It is ideal for harsh environment applications.

Features

  • 50 mm Diameter Black Aluminum Anodised housing
  • Double Ball Bearings
  • 8 mm Stainless Steel ‘D’ cut Shaft
  • Servo Mounting or three M3 Screws at 32mm PCD
  • Low operating torque
  • Connector with cable

Specifications

Angle of Rotation 0~360° Clockwise rotation (Endless), can be factory programmed for
45°,90°, 180° and Counter Clockwise Rotation (CCW)
Auxiliary Supply (Vss) 9VDC to 30VDC±10%, 25mA max
Output 0-10VDC (Load ≥ 2KΩ), 4-20mA (Load ≥ 600Ω)
Total Independent linearity ≤0.70 (with respect to best line fit and over full temperature range) for V & mA output
Resolution 10 bit (0.35°) over 360° for 360° range
11 bit (0.176°) over 180° for 180° range
12 bit (0.088°) over 90° for 90° range
12 bit (0.088°) over 45° for 45° range
External Magnetic Field Effect Small effect due to Differential measuring technique & sensor conditioning circuitry. (It is desirable to mount encoder away from strong magnetic field, at least 100mm
Maximum Angular Shaft Speed 3000RPM. Number of samples per revolution decreases as the speed of rotation increases. Accuracy of output is not affected by Speed
Operating Temperature Range 0°~70°C
Temperature Compensation No external compensation required
Insulation Resistance 2MΩ min. @ 500VDC
H.V. Test No damage for 1 min at 250VAC
Rotational life 100 million
Protection Class IP-65

 

Applications

  • Automation,
  • Test and Measuring Instruments,
  • Crane, Angle Measurement,
  • Printing Industries,
  • Robotics & many more.

Options

NCP-711-V (0 to 10VDC)
V/45°, CW or CCW
V/90°, CW or CCW
V/180°, CW or CCW
V/360°, CW or CCW – (Standard V)

NCP-711-S (V = 0 to 10VDC & Io = 4 to 20mA)
S/45°, CW or CCW
S/90°, CW or CCW
S/180°, CW or CCW
S/360°, CW or CCW – (Standard V & I)

Dimensional Diagram

ncp711-d

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

VE-360

10 Bit MINI Absolute Analogue Encoder, VE-360

The new product in PANKAJ Basket, Model VE-360 to provide Solid state analogue output on panel mounting manually actuation using contactless Hall’s effect technology. Burg pin connector’s makes termination connection easy.

The product is also available, pre programmed with effective rotational angle of 45º, 90º, 180º and 360º in CW and CCW.

Features

  • 25 mm Ø, 12 mm height Moulded housing
  • 3/8″ x 32 TPI, 10mm long Brass Nickle Plated Bush
  • 6.35 mm Ø, 15 mm long Brass Nickel plated Shaft

Specifications

Angle of Rotation 0~360° Clockwise rotation (Endless), can be factory programmed for
termination connection easy.
180°,90°, 45° and Counter Clockwise rotation
Auxiliary Supply (Vss) 5VDC±10%, 25mA max
Output 0-Vss, Ratio metric with supply (Load ≥ 2KΩ)
Total Independent linearity ±0.7° (with respect to best line fit and over full temperature range)
Resolution 10 bit (0.35°) over 360° for 360° range,
11 bit (0.176°) over 180° for 180° range,
12 bit (0.088°) over 90° for 90° range,
12 bit (0.088°) over 45° for 45° range
External Magnetic Field Effect Negligible effect due to Differential Measuring technique &
sensor conditioning circuitry. (It is desirable to mount encoder
away from strong magnetic field, at least 100mm
Maximum Angular Shaft Speed 100RPM. Number of samples per revolution decreases as the speed
of rotation increases. Accuracy of output is not affected by Speed
Operating Temperature Range 0°~70°C
Temperature Compensation No external compensation required
Insulation Resistance 2000MΩ min. @ 500VDC
H.V. Test No damage for 1 min at 250VAC
Protection with 100mA fast blow fuse in series with supply a. Reverse polarity protection,
b. Maximum auxiliary supply up to 35VDC,
c. voltage output short circuit protected to ground rail
Rotational life 1 million
Protection Class IP-40
Fixing Method 3/8” x 32 TPI ME bush
Size Refer Drawing
Casing Material Reinforced Polyamide
Shaft Material Nickel Plated Brass
Weight 22gm

Functional Description

Contactless measurement technique gives output in ratio metric with supply voltage. Output voltage is
taken out through berge pin connection as marked on housing or wires can be directly soldered on
gold plated output PCB terminals.

Sample Rates

Sampling Rate, n = 60/(RPM x 384μs).
e.g. RPM = 60, then n = 60/(60 x 384 x 10-6) = 2604 samples/second.

Product Image

ve-360

Dimensional Diagram

ve-33-2

Applications

  • Automation,
  • Test and Measuring Instruments,
  • Robotics,

Ordering Information Example: VE-90

Model No. Angle of Rotation
VE 0°/360°, 45°, 90°, 180°

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

MINI SSI Encoder

10 Bit MINI Absolute Analogue Encoder Model: MINI SSI Encoder

The new product in PANKAJ Basket, Model SSIE-360 to provide Solid State Analogue output on panel mounting manually actuation, using contactless Hall’s effect technology. Burg pin connector’s makes termination connection easy. The product is also available, pre programmed with effective rotational angle of 45 , 90 , 180 and 360 0 0 0 0 in CW and CCW.

Features

  • 25 mm Ø, 12 mm height Moulded housing
  • 3/8″ x 32 TPI, 10mm long Brass Nickle Plated Bush
  • 6.35 mm Ø, 15 mm long Brass Nickel plated Shaft

Specifications

Angle of Rotation 0~3600 Clockwise rotation (Endless), can be factory programmed for
termination connection easy.
180°,90°, 45° and Counter Clockwise rotation
Auxiliary Supply (Vss) 5VDC±10%, 25mA max
Output SSI
Total Independent linearity ±0.35º (with respect to best line fit and over full temperature range)
Resolution 10 bit (0.35º) over 360º for 360º range,
11 bit (0.176º) over 180º for 180º range,
12 bit (0.088º) over 90º for 90º range,
12 bit (0.088º) over 45º for 45º range
External Magnetic Field Effect Negligible effect due to Differential Measuring technique &
sensor conditioning circuitry. (It is desirable to mount encoder
away from strong magnetic field, at least 100mm
Maximum Angular Shaft Speed 100RPM. Number of samples per revolution decreases as the speed
of rotation increases. Accuracy of output is not affected by Speed
Operating Temperature Range 0º~70ºC
Temperature Compensation No external compensation required
Insulation Resistance 2000MΩ min. @ 500VDC
H.V. Test No damage for 1 min at 250VAC
Protection with 100mA fast blow fuse in series with supply a. Reverse polarity protection,
b. Maximum auxiliary supply up to 35VDC,
c. voltage output short circuit protected to ground rail
Rotational life 1 million
Protection Class IP-40
Fixing Method 3/8” x 32 TPI ME bush
Size Refer Drawing
Casing Material Reinforced Polyamide
Shaft Material Nickel Plated Brass
Weight 25gm

Functional Description

Contact less measurement technique gives output in SSI-Synchronous Serial Interface form. Outputs are taken out through berge pin connection as marked on housing or wires can be directly soldered on gold plated output PCB terminals. When CS is at logic low (active), DO will change to High from High Impedance state. After 500ns (CLKFE) time data is latched into shift register with first falling edge of CLK. With subsequent rising edge of CLK pulse, one data bit shifts out at DO. Word contains 16 bit. First 10 bits, D9 to D0 are angle information. D9 is MSB and D0 is LSB of angle information.

Subsequent 6 bits are for system information viz.:

1. OCF – Offset Compensation Finished; OC algorithm has finished and data is valid if logic High,
2. COF – Cordic OverFlow; Logic High indicates an out of range error in the cordic part,
data D9 to D0 is invalid. (Send the encoder to manufacturer).
3. LIN – LINearity Alarm; Field generates a critical output linearity when logic High, data D9 to D0
may still be used but may contain invalid data. (Send the encoder to manufacturer).
4. MagInc – Magnitude Increase, field intensity is increasing, check the external magnetic disturbance.
5. MagDec – Magnitude Decrease, field intensity is decreasing, check the external magnetic disturbance.
Both above (4. & 5.) at logic High indicates magnetic field strength is below or above the required limit.
Check for external magnetic influence. If not i.e. field strength is out of range, send the encoder to factory.
Even Parity – bit for transmission error detection of bits 1 to 15 (D9…D0, OCF, COF, LIN, MagInc, DecMag).

Other Functionality:

Sampling Rate: n = 60/(RPM x 384μs).
Sampling Rate e.g. RPM = 60, then n = 60/(100 x 384 x 10-6) = 1562 samples/second.
MagRngn – Magnet Field Magnitude Range Warning (Optional), it is combination of MagInc and MagDec.
Active Low via open drain output, requires an external pull-up resistor. If the magnetic field is in range,
this output is turned off (logic High).

ss-1e-330

Applications

  • Automation,
  • Test and Measuring Instruments,
  • Robotics,
  • Crane, Angle Measurement.
Model No. Angle of Rotation
SSIE 0°/360°, 45°, 90°, 180°

Product Image

ss-1e-330

Dimensional Diagram

ss-ie-330-2

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice