+91 22 2446 5778

SSIE-360

10 Bit MINI Absolute Analogue Encoder – SSIE-360

The new product in PANKAJ Basket, Model SSIE-360 to provide Solid State Analogue output on panel mounting manually actuation, using contactless Hall’s effect technology. Burg pin connector’s makes termination connection easy.

The product is also available, pre programmed with effective rotational angle of 45º, 90º, 180º  and 360º in CW and CCW.

Features

  • 25 mm Ø, 12 mm height Moulded housing
  • 3/8″ x 32 TPI, 10mm long Brass Nickle Plated Bush
  • 6.35 mm Ø, 15 mm long Brass Nickel plated Shaft

Specifications

Angle of Rotation 0~3600 Clockwise rotation (Endless), can be factory programmed for
termination connection easy.
180°,90°, 45° and Counter Clockwise rotation
Auxiliary Supply (Vss) 5VDC±10%, 25mA max
Output SSI
Total Independent linearity ±0.35º (with respect to best line fit and over full temperature range)
Resolution 10 bit (0.35º) over 360º for 360º range,
11 bit (0.176º) over 180º for 180º range,
12 bit (0.088º) over 90º for 90º range,
12 bit (0.088º) over 45º for 45º range
External Magnetic Field Effect Negligible effect due to Differential Measuring technique &
sensor conditioning circuitry. (It is desirable to mount encoder
away from strong magnetic field, at least 100mm
Maximum Angular Shaft Speed 100RPM. Number of samples per revolution decreases as the speed
of rotation increases. Accuracy of output is not affected by Speed
Operating Temperature Range 0º~70ºC
Temperature Compensation No external compensation required
Insulation Resistance 2000MΩ min. @ 500VDC
H.V. Test No damage for 1 min at 250VAC
Protection with 100mA fast blow fuse in series with supply a. Reverse polarity protection,
b. Maximum auxiliary supply up to 35VDC,
c. voltage output short circuit protected to ground rail
Rotational life 1 million
Protection Class IP-40
Fixing Method 3/8” x 32 TPI ME bush
Size Refer Drawing
Casing Material Reinforced Polyamide
Shaft Material Nickel Plated Brass
Weight 25gm

Functional Description

Contact less measurement technique gives output in SSI-Synchronous Serial Interface form. Outputs are
taken out through berge pin connection as marked on housing or wires can be directly soldered on gold
plated output PCB terminals.
When CS is at logic low (active), DO will change to High from High Impedance state. After 500ns (CLKFE)
time data is latched into shift register with first falling edge of CLK. With subsequent rising edge of CLK
pulse, one data bit shifts out at DO. Word contains 16 bit. First 10 bits, D9 to D0 are angle information. D9
is MSB and D0 is LSB of angle information.

Subsequent 6 bits are for system information viz.:

1. OCF – Offset Compensation Finished; OC algorithm has finished and data is valid if logic High,
2. COF – Cordic OverFlow; Logic High indicates an out of range error in the cordic part,
data D9 to D0 is invalid. (Send the encoder to manufacturer).
3. LIN – LINearity Alarm; Field generates a critical output linearity when logic High, data D9 to D0
may still be used but may contain invalid data. (Send the encoder to manufacturer).
4. MagInc – Magnitude Increase, field intensity is increasing, check the external magnetic disturbance.
5. MagDec – Magnitude Decrease, field intensity is decreasing, check the external magnetic disturbance.
Both above (4. & 5.) at logic High indicates magnetic field strength is below or above the required limit.
Check for external magnetic influence. If not i.e. field strength is out of range, send the encoder to factory.
Even Parity – bit for transmission error detection of bits 1 to 15 (D9…D0, OCF, COF, LIN, MagInc, DecMag).

Other Functionality:

Sampling Rate: n = 60/(RPM x 384μs).
Sampling Rate e.g. RPM = 60, then n = 60/(100 x 384 x 10-6) = 1562 samples/second.
MagRngn – Magnet Field Magnitude Range Warning (Optional), it is combination of MagInc and MagDec.
Active Low via open drain output, requires an external pull-up resistor. If the magnetic field is in range,
this output is turned off (logic High).

ss-1e-330

Applications

  • Automation,
  • Test and Measuring Instruments,
  • Robotics,
  • Crane, Angle Measurement.
Model No. Angle of Rotation
SSIE 0°/360°, 45°, 90°, 180°

Product Image

ss-1e-330

Dimensional Diagram

ss-ie-330-2

Note: We reserve the right to make any kind of design, specifications or functional modification at any moment without prior notice

Enquiry Form

Your Name (required)

Your Email (required)

Your Message

Secrete Code

Menu